REVIEW: $30 Digital TPMS – 6 Month Review | Energizer CR 1632 batteries

Six months after installing the $30 Digital Tire Pressure Monitoring System ( https://amzn.to/2ncBVf6 ) on my Honda Clarity and Accord, two of the sensors started to have errors. I found out two batteries that came with the set was low so i replaced them with Energizer CR1632 ( https://amzn.to/3gpfo4q ). Hopefully we will find out how long these batteries last on teh TPMS sensors. Btw, my Youtube vlogs and reviews may also have associated affiliate links to products that may earn from qualifying purchases.

My new 2018 Honda Clarity and 2007 Honda Accord does not have a TPMS system that tells tire pressure and temperature of the tires. My 2007 Accord simply didnt have TPMS . My 2018 Honda Clarity on checks tire rotation to determine if the diameter is smaller to indicate over or under inflation of the tires. I loved my Chevy Volt which has individual meters for each tire. Individual guage allowed me to monitor status and if I had a air leak. Good for finding a tire leak before a flat tire.

The kit is solar powered with a battery and a USB input for 5 volt power. This makes it convenient to be wire free when i put it on my dash. In order to keep the unit from flying off my dash board, I added Scotch double sided tape ( https://amzn.to/2pCOvFr ) on the bottom of the TPMS unit and added anti-slip shelving mat foam ( https://amzn.to/2nULpfs ) . You could have just used a cell phone anti-slip mat ( https://amzn.to/2n7sZre ) .

I charged the kit in a USB charger for 2 hours before installing kit. The kit was already calibrated for all four tires of the car: Front Right, Front Left, Rear Right, Rear Left. You just need add the locking nut onto the tire nipple, then add the sensor to the corresponding tire location. Use the provided mini spanner / wrench to tighten the nuts against the TPMS sensor. You are able to set the high and low pressure alarm and units settings such as PSI vs BAR or F vs C. In a few minutes the main controller receives tire data from the individual tires.

I tested the tire pressure against my digital tire pressure gauge (https://amzn.to/2naQQGH ) and fount it accurate.

Thank you for visiting and supporting SterlingW Youtube Channel!
Thanks for watching! Like, Subscribe, Leave a comment, and click the Bell button!

SOCIAL MEDIA:
Join me on Youtube: https://youtu.be/TFuoiaWgvc4
Instagram: https://www.instagram.com/sterling.wong
Twitter: https://twitter.com/sterlingwong8 ( @sterlingwong8 )
Website: http://www.sterlingwong.com

Disclaimer:
This is what i do for entertainment and your viewing entertainment! Some of the stuff are entertaining, while some are just plain silly. If you do anything with your own property, you do so at your own risk.
Due to factors beyond the control of Sterlingwong, I cannot guarantee against improper use or unauthorized modifications of this information. This information is for entertainment only. Sterlingwong assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. Sterlingwong recommends safe practices when working on personal property , vehicles, and / or with tools seen or implied in this video. Due to factors beyond the control of Sterlingwong, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Sterlingwong.




DIY: Installing Deer Warning Whistles! – Why you should use screws instead of mounting tape.

So there’s been more deer around and I figured I get a some deer warning whistles and put them on my Honda Clarity . They sell similar ones online: https://amzn.to/2RfUax1 . I used screws to mount to the front of my car.

The two deer warning whistle attached on to the bumper with foam adhesive tape. There are screw holes on the mounts, however the foam tape holds it fine for about 2 years.

It finally tore the foam and the other one ripped off due to wind speed. This time around i drilled two pilot holes and added two flat head screws. I used a 1/16 drill bit ( https://amzn.to/3hc9Ziz ) on my Ryobi power drill (https://amzn.to/30quh1O ). I had to use aluminum tape (https://amzn.to/2Yl5Xvv) to make the small drill bit see my video of how i did it.

So my there are two types of whistles included in the package, one with closed back end and one with a open back end. The closed one is louder is placed on the passenger side. The open one is quieter and is placed on the driver side. When driving at highway speeds I can hear the passenger side with the passenger window down.

Enjoy and hope this helps!

Thank you for visiting and supporting SterlingW Youtube Channel!
Thanks for watching! Like, Subscribe, Leave a comment, and click the Bell button!

Thank you for visiting and supporting SterlingW Youtube Channel!
Thanks for watching! Like, Subscribe, Leave a comment, and click the Bell button!

SOCIAL MEDIA:
Join me on Youtube: https://youtu.be/TFuoiaWgvc4
Instagram: https://www.instagram.com/sterling.wong
Twitter: https://twitter.com/sterlingwong8 ( @sterlingwong8 )
Website: http://www.sterlingwong.com

Disclaimer:
This is what i do for entertainment and your viewing entertainment! Some of the stuff are entertaining, while some are just plain silly. If you do anything with your own property, you do so at your own risk.
Due to factors beyond the control of Sterlingwong, I cannot guarantee against improper use or unauthorized modifications of this information. This information is for entertainment only. Sterlingwong assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. Sterlingwong recommends safe practices when working on personal property , vehicles, and / or with tools seen or implied in this video. Due to factors beyond the control of Sterlingwong, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Sterlingwong.



How to use SMALL DRILL BITS on a DRILL Chucks

If you need to use a small drill bit on a regular drill chuck to drill pilot holes, you will notice the new chucks have gaps. I love my Ryobi 18v power drill which i bought from a kit (https://amzn.to/30quh1O ) it has a newer chuck that has teeth to hold round drill bits better, however the gap too big for small drill bits such as 1/16 and 3/64 bits from my bit set ( https://amzn.to/3hc9Ziz ). I like staying on one platform of tools to share the family of Ryobi 18v battery ( https://amzn.to/3cPX0zM ). Btw, my Youtube vlogs and reviews may also have associated affiliate links to products that may earn from qualifying purchases.

For years I have used Aluminum Tape ( https://amzn.to/2Yl5Xvv ) to use smaller bits. I basically cut a 1.5 centimetre 4 inch strip. I wrap the tape around the bit. I then use the drill chuck to compress the aluminum tape for a strong grip. After adding the tape, it will stay on the drill bit for the life of the bit. Usually they kits come with multiple small bits as they are meant for pilot holes and drilling delicate materials.

They do sell Small Drill Bit Chuck adapters ( https://amzn.to/30o0DdH ) that work if you plan to keep your drill bits original. They are delicate and solves this problem as normal small drill bits are not meant to be drilled with a lot of pressure or force.

Items used or mentioned in this article video:
Aluminum Tape: https://amzn.to/2Yl5Xvv
Small Drill Bit Chuck adaptor https://amzn.to/30o0DdH
Aluminum Tape: https://amzn.to/2Yl5Xvv

Ryobi 18v power tools kits: https://amzn.to/30quh1O
Ryobi Drill bit sets: https://amzn.to/3hc9Ziz
Ryobi 18v battery: https://amzn.to/3cPX0zM

Thank you for visiting and supporting SterlingW Youtube Channel!
Thanks for watching! Like, Subscribe, Leave a comment, and click the Bell button!

Thank you for visiting and supporting SterlingW Youtube Channel!
Thanks for watching! Like, Subscribe, Leave a comment, and click the Bell button!

SOCIAL MEDIA:
Join me on Youtube: https://youtu.be/TFuoiaWgvc4
Instagram: https://www.instagram.com/sterling.wong
Twitter: https://twitter.com/sterlingwong8 ( @sterlingwong8 )
Website: http://www.sterlingwong.com

Disclaimer:
This is what i do for entertainment and your viewing entertainment! Some of the stuff are entertaining, while some are just plain silly. If you do anything with your own property, you do so at your own risk.
Due to factors beyond the control of Sterlingwong, I cannot guarantee against improper use or unauthorized modifications of this information. This information is for entertainment only. Sterlingwong assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. Sterlingwong recommends safe practices when working on personal property , vehicles, and / or with tools seen or implied in this video. Due to factors beyond the control of Sterlingwong, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Sterlingwong.